GOMAX Quadra DN2 Capillary Hose 1 m | Straight x 90° Elbow 1/4" Flare | AC & Refrigeration
GOMAX Quadra DN2 Capillary Hose 1 m | Straight x 90° Elbow 1/4" Flare | AC & Refrigeration
Couldn't load pickup availability
Share
Looking for a capillary hose that turns a corner? This 1 m GOMAX Quadra DN2 hose comes already assembled with a straight 1/4" SAE flare (7/16-20 UNF) female brass fitting on one end and a 90° elbow fitting on the other. The elbow lets the hose leave a port at a right angle, which helps when a gauge, pressure switch or service port sits close to a panel or another component.
Why Choose the 1 m Straight x 90° Elbow Capillary Hose?
- Right-angle exit: The 90° elbow end avoids a sharp bend in the hose right at the fitting, which protects the hose in tight spaces.
- Straight end where you need it: The other end is a standard straight fitting, so one hose covers a port that faces forward and one that faces sideways.
- Already assembled: The brass fittings are fitted to the hose, so there is no cutting, crimping or brazing on site.
- Absorbs compressor vibration: The flexible hose copes with movement that can crack rigid copper capillary tube.
- Black or orange: Use the colour to separate lines on a crowded unit.
Capillary Hose 1 m Straight x Elbow Specifications
| Feature | Detail |
|---|---|
| Assembly | 1 m long hose, straight fitting on one end and 90° elbow fitting on the other |
| Length | 1 m |
| End fitting 1 | Straight female brass fitting, 1/4" SAE flare (7/16-20 UNF) |
| End fitting 2 | 90° female elbow brass fitting, 1/4" SAE flare (7/16-20 UNF) |
| Hose | GOMAX Quadra DN2 flexible thermoplastic capillary hose |
| Inner / outer diameter | 2 mm (0.079 in) / 6.1 mm (0.240 in) |
| Minimum bend radius | 10 mm (0.394 in) |
| Working pressure | 120 bar (12 MPa, 1,740 psi) |
| Burst pressure | 600 bar (60 MPa, 8,700 psi) |
| Temperature range | -45 °C to +130 °C (-49 °F to +266 °F) |
| Construction | Thermoplastic inner tube (nylon liner), high-tensile polyester braid, laser-branded thermoplastic cover |
| Hose colour | Black (hose 0780BC) or Orange (hose 0780C) |
Refrigerants and Oils
The nylon liner and copper-alloy fittings are chemically compatible with common HFC and HFO refrigerants such as R32, R134a, R404A, R407C, R410A, R454B, R513A and R1234yf, as well as R22, and GOMAX also states compatibility with subcritical CO2 and propane R290. Mineral, PAO, POE and PAG oils are fine. Always check your own system's refrigerant and pressure rating.
How to Install an Elbow Capillary Hose
Decide which end gets the elbow
Put the 90° elbow on the port that has the least room around it, such as a gauge or switch port close to a panel. Put the straight end on the port that has clear space in front of it.
Check the direction before the final tightening
Offer the elbow up to its port and check which way the hose will leave. Then tighten the nut. Do not turn or move the hose after it is tight, because that can loosen the nut or damage the seal. If you need a different direction, undo the nut, reposition the hose and tighten it again.
Leave a gentle curve
Route the hose in a smooth curve above the 10 mm minimum bend radius, away from hot surfaces and sharp edges.
Where to Use It: Applications
- Gauge and pressure switch ports close to panels or other components
- Compact condensing units and rooftop units with limited clearance
- Pressure test points that face sideways or upward
- Oil equalisation and oil return lines in tight compressor compartments
Why Buy an Elbow Capillary Hose from Angstrom in Dubai?
- Dubai-based supplier of AC and refrigeration components, with delivery across the UAE.
- Assembled GOMAX Quadra hose with the manufacturer's hose part numbers, so it matches your parts list.
- A straight x straight version as well, if your ports line up and you do not need the elbow.
Straight x Elbow Capillary Hose FAQ
What is the benefit of the 90° elbow end?
It lets the hose leave the port at a right angle, so the hose does not need a tight bend next to the fitting. That helps in cramped spaces.
How long is the hose?
The assembled hose is 1 m long.
What fittings are on each end?
One end has a straight female 1/4" SAE flare (7/16-20 UNF) brass fitting. The other end has a 90° female elbow fitting with the same 1/4" SAE flare thread.
Can I rotate the elbow after it is connected?
Set the direction while you tighten the nut. To change it later, undo the nut, set the new direction and tighten it again. Do not twist the hose while it is connected.
Is it suitable for R410A and R32 systems?
The Quadra hose is chemically compatible with R410A and R32, and its working pressure is 120 bar (1,740 psi). Check that this rating covers your system.
Is there a version without the elbow?
Yes. The 1 m straight x straight version has a straight fitting on both ends and suits ports that line up.



