GOMAX Quadra DN2 Capillary Hose 1 m | Straight x Straight 1/4" Flare | AC & Refrigeration
GOMAX Quadra DN2 Capillary Hose 1 m | Straight x Straight 1/4" Flare | AC & Refrigeration
Couldn't load pickup availability
Share
Need a straight, ready-made capillary hose for an AC or refrigeration unit? This is a 1 m GOMAX Quadra DN2 capillary hose, already assembled with a straight 1/4" SAE flare (7/16-20 UNF) female brass fitting on each end. Connect it between two ports that line up, such as a service port and a pressure gauge or pressure switch, with no cutting, crimping or brazing on site.
Why Choose the 1 m Straight x Straight Capillary Hose?
- Ready to fit: The hose arrives already fitted with its brass flare fittings, so installation is a matter of connecting both ends and tightening the nuts.
- Straight at both ends: A good match for ports that face the hose run directly, such as a gauge or switch mounted in line with the service port.
- Absorbs compressor vibration: The flexible hose copes with movement that can crack rigid copper capillary tube.
- Black or orange: Pick the colour that helps you tell one line from another on the unit.
- Standard 1/4" flare: The female 1/4" SAE flare ends suit common refrigeration service and instrument ports.
Capillary Hose 1 m Straight Specifications
| Feature | Detail |
|---|---|
| Assembly | 1 m long hose with a straight fitting on both ends |
| Length | 1 m |
| End fittings | Straight female brass fitting, 1/4" SAE flare (7/16-20 UNF), both ends |
| Hose | GOMAX Quadra DN2 flexible thermoplastic capillary hose |
| Inner / outer diameter | 2 mm (0.079 in) / 6.1 mm (0.240 in) |
| Minimum bend radius | 10 mm (0.394 in) |
| Working pressure | 120 bar (12 MPa, 1,740 psi) |
| Burst pressure | 600 bar (60 MPa, 8,700 psi) |
| Temperature range | -45 °C to +130 °C (-49 °F to +266 °F) |
| Construction | Thermoplastic inner tube (nylon liner), high-tensile polyester braid, laser-branded thermoplastic cover |
| Hose colour | Black (hose 0780BC) or Orange (hose 0780C) |
Refrigerants and Oils
The nylon liner and copper-alloy fittings of the Quadra system are chemically compatible with common HFC and HFO refrigerants such as R32, R134a, R404A, R407C, R410A, R454B, R513A and R1234yf, as well as R22. GOMAX also states compatibility with subcritical CO2 and propane R290. The hose works with mineral, PAO, POE and PAG oils. Check your system's refrigerant and pressure before you choose a hose.
How to Connect It
Check the ports first
Make sure both ports are 1/4" male SAE flare (7/16-20 UNF) and that they sit roughly in line, so the hose runs straight without a hard kink. If one port faces sideways, the straight x 90° elbow version is usually easier to route.
Tighten without twisting the hose
Seat each fitting on its port and tighten the nut. Hold the hose still while you tighten, because turning the hose after it is fitted can loosen the nut or damage the seal. Keep the bend radius above 10 mm.
Where to Use It: Applications
- Pressure gauge and manometer connections on AC and refrigeration units
- High, low and oil pressure switch lines
- Pressure test points and service connections
- Oil equalisation lines between compressors
Why Buy from Angstrom in Dubai?
- Dubai-based supplier of AC and refrigeration components, with delivery across the UAE.
- Assembled GOMAX Quadra hose with the manufacturer's hose part numbers, so it matches your parts list.
- A straight and a 90° elbow version, so you can pick the one that suits your routing.
Straight Capillary Hose FAQ
How long is this capillary hose?
The assembled hose is 1 m long.
What fittings does it have?
A straight female 1/4" SAE flare (7/16-20 UNF) brass fitting on each end.
Do I need to crimp or braze anything?
No. The fittings are already fitted to the hose. You only connect the ends to your ports.
What is the difference between the black and the orange hose?
Only the colour of the cover. Both have the same size, pressure rating and temperature range.
What pressure can it handle?
The working pressure of the Quadra DN2 hose is 120 bar (1,740 psi), and the burst pressure is 600 bar (8,700 psi).
When should I choose the straight x elbow version instead?
Choose the elbow version when a port faces sideways or space is tight, so the hose can leave the fitting at a right angle without bending sharply.



